Unique Weather Conditions in Unterwössen
All text and images on this page: Jan Lyczywek


Slope
Why does the slope blow?
There are three different mechanisms that can cause the slope to blow: valley wind, regional wind, and incoming cold air.

Slope lift caused by valley wind

Achental.jpeg

The Achental valley wind system is responsible for the vast majority of good slope-wind days. For this to happen, we first need a day with good large-scale thermals and unobstructed sunlight. On such a day, the thermals over the mountains will start earlier, be stronger, and reach higher than those over the lowlands—in short, the thermals over the mountains will be better than those in the lowlands. The best thermals are found on the highest mountains near the main Alpine ridge, as well as over the long south-facing slopes of the inner-Alpine longitudinal valleys (e.g., Pinzgau) and over the steep rock faces of the Kalkalpen (e.g., Wilder Kaiser, Loferer Steinberge, etc.). There, a great deal of air is pumped upward, along the warm slopes and further up into the thermal currents above. The supply of air masses for these intra-Alpine thermals essentially comes through those valleys that provide the most direct connection from the lowlands—where thermals are weaker—to the mountains, where thermals are strong. In such valleys, the air flowsvalleyward, into the mountains. That is why this flow is also called a valley wind or, more precisely,a valley inflow. A typical characteristic of the valley inflow is that it reaches its maximum speed very low down on the valley floor, perhaps 100–300 meters above the valley floor. The valley inflow always sets in several hours after the thermals begin—after all, the thermals in the high mountains must first become strong enough that they can no longer meet their need for a supply of air from their immediate surroundings.

One could also say that the intra-Alpine thermals create an “intra-Alpine heat trough” in the valleys. In the connecting valleys between the lowlands and the thermal mountains, there is thus a pressure gradient flowing into this heat trough. This pressure gradient drives the valley winds in the connecting valleys. The valley winds thus attempt to fill the intra-Alpine heat trough, while the intra-Alpine thermal activity maintains the heat trough.

Our river, the Tiroler Ache, rises about 45 km south of the airfield at Pass Thurn and flows from there in a fairly straight line northward into Lake Chiemsee. As a result, the Achental Valley provides a direct connection—almost the shortest route—from the Upper Bavarian lowlands southward to the thermal areas of the Pinzgau and the Hohe Tauern. This makes the Achental Valley an ideal flow channel for supplying the intra-Alpine thermals with a fresh supply of air from the lowlands, where thermals are weaker. The Achental Valley’s valley-inflow system is correspondingly strong.

Now, such a valley wind is, in and of itself, pretty much useless for gliding. By definition, a valley wind blows into the valley and thus runs parallel to it. It has no reason to generate any updrafts on the left or right sides of the valley. In addition, it stirs up the air at the bottom of the valley, destroying any faint thermal bubbles there and sweeping away any warm air that might be present on the valley floor, feeding it into the (already strong) intra-Alpine thermals.

The valley wind generates a slope lift only in two cases:
1. when a slope, a foothill, or a ridge extends across the valley and the valley wind strikes it as nearly at a right angle as possible, so that it must flow over the obstacle.
2. when the entire valley makes a curve or a bend. The slopes on the outside of this curve attempt to deflect the direction of the valley wind; in the process, the wind shoots up the slopes of the outer curve for a short distance.
In both cases, paragliders and hang gliders use the apt term “impact slope,” because the valley wind collides with the slope here.

Our Gscheurer Wand is a mixture of both types of wind-sheltered slopes: on the one hand, it—especially its easternmost, lowest part (the Balsberg-Nase)—stands as a ridge across the path of the secondary branch of the valley wind flowing straight from Marquartstein toward Oberwössen. On the other hand, the Gscheurer Wall deflects the main branch of the valley wind—which flows into the valley from Marquartstein—toward Schleching, thus forming the outer curve of a bend in the valley. Incidentally, this is also the reason why the slope west of the turning point marked by the summit cross is no longer viable: here, the deflection ends, and the valley wind is already flowing parallel to the slope again. You can see this very clearly from the windsocks at the winch and at the launch site.

Taleinwind.jpeg

Whether the valley wind actually generates usable slope lift, however, depends not only on wind speed. The thickness of the valley wind layer is also important. On good thermal days, when the slope provides strong and high lift, experience shows that the valley wind near Unterwössen reaches a layer thickness of about 500 meters in the late afternoon; the slope can then easily take you up to 700–800 meters above the launch site.

Unfortunately, the strength of the surface wind is not an indicator of the thickness of this valley-inflow layer. On the contrary: external factors can limit the layer’s thickness—for example, a low-level inversion or a supraregional wind blowing from the opposite (i.e., south to west) direction. Under such a lid, the valley wind is left with only a narrowed flow channel for the air mass it carries in. At the ground level, the wind speed then increases, precisely because the thickness of the valley inflow layer is reduced. On days like these, flying on the slope can be frustrating: it’s blowing like crazy at the bottom, the wind socks on the wind towers and launch huts are pointing horizontally—“it has to work”—and yet the slope provides poor lift and, above all, doesn’t carry you very high.

In the past, the wind blowing into the Achental valley was often referred to as the “Chiemseewind.” At first glance, this isn’t incorrect, since every wind is named after the direction from which it blows. Viewed from the Achental, the wind does indeed appear to come from Lake Chiemsee. Nevertheless, the term is misleading, because Lake Chiemsee is not the cause of the wind blowing into the valley. As described above, the cause is exclusively the strong thermal currents in the high mountains. One might argue that the cool lake creates a downward air movement and thus supports the valley wind system from its side. However, the fact that this contribution is negligible is evident from the equally strong valley wind systems in Alpine valleys leading to the lowlands that lack a lake at the valley mouth, such as the Inn Valley. We therefore have no reason to fear the gradual silting up of Lake Chiemsee, even in the long term.

In the evening, the valley breeze often persists for a long time, even though there are no longer any thermals in the airfield area. This is partly because the thermals in the high mountains—which drive the valley breeze—die down much later in the evening than the thermals in the lower Alpine foothills. But even long after the thermals have completely died down, the air that has been set in motion continues to flow valleyward due to its own inertia.

Slope lift caused by winds from outside the region

Brute Force.jpeg

Of course, any slope can function even without a local upslope wind system. Even large-scale winds can generate slope lift if they are strong enough and strike the slope at as close to a right angle as possible. By “large-scale winds,” we mean the wind currents caused by large high- and low-pressure systems that extend over several hundred kilometers, as can be seen, for example, in the pressure distribution on a Europe-wide weather map. Large-scale winds are sometimes also referred to as synoptic-scale winds.

In the low mountain ranges, wind from outside the region is likely the most important driver of slope lift, since these ranges generally do not generate sufficiently strong valley-inflow systems. Even on isolated slopes in the lowlands, wind from outside the region is by far the most important—and often the only—driver. But even in the Alps, long distances (1,000 km and more) are flown in slope updrafts generated by regional winds, namely during a north foehn or south foehn (although in these weather conditions, lee waves often occur in addition to the slope updraft; that is another topic).

Our Unterwössener slope can also be “forced” to function by winds from outside the region. For this to happen, the wind must pass through the valley entrance and hit our slope. Based on the orography, this should work best with a northeasterly wind from outside the region. Experience shows, however, that the Gscheurer Wand can also perform well when a pure easterly wind is blowing in the Alpine foothills outside the valley. The base of the Alpine ridge from Bergen to Marquartstein forms a gentle curve that apparently directs the easterly wind quite efficiently into the valley entrance; the eastern flank of the Hochplatte helps from the other side. Furthermore, easterly conditions here are usually driven by subsidence within a high-pressure system (“anticyclonic”), so that anticyclonic easterly winds are strongest near the ground (where we need them for slope lift). A drawback of easterly conditions, however, is the typically quite stable air mass from the high-pressure system. Stable air is not very inclined to flow up the slope as an updraft. Despite relatively high wind speeds at the ground, the slope lift is therefore sometimes only comparatively weak and/or extends only to moderate altitudes when easterly winds prevail.

Generally speaking, the weather conditions on days when a widespread north, northeast, or even east wind forces our slope to “give in” don’t look particularly inviting. The more of a northerly component the wind has, the more pronounced the northern wind-blocking effects often are. But even with easterly conditions, a leaden-gray, low-lying stratus layer often gets trapped along the edge of the Alps beneath the subsidence inversion of the high-pressure system. When the slope takes off on such days, it often comes as a bit of a surprise to many pilots given the ominous-looking weather conditions.

Unlike thermally induced valley winds, long-range winds are largely independent of the time of day. That is why the slope can be driven by “brute force”—that is, by long-range winds—even early in the morning.

Slope lift caused by an inflow of cold air

Cold-Air Injection.jpeg

The third mechanism for generating slope lift is by far the rarest, but perhaps the most interesting. It can be observed, for example, ahead of an approaching cold front or a summer thunderstorm front. The regional wind typically comes from the west; ahead of the front, it tends to be from the southwest, and behind it, from the northwest. The front moves slowly from west to east, usually a bit faster in the flat, unobstructed Alpine foothills than in the mountains, where it is slowed by the rugged terrain. Along the front line, heavy precipitation falls from individual shower cells. The rain cools the air through which it falls via evaporation. The air, now cooled and thus denser, descends with the rain. Then the cold air hits the ground and shoots forward as a flat tongue of cold air along the ground ahead of the actual front, also from west to east. Over unobstructed flatlands, this cold air tongue can extend far ahead. In the Bavarian Alpine foothills, the edge of the Alps—which rises abruptly from the flatlands—acts as a “guardrail,” further preventing the cold air tongue from spreading laterally to the south. This “guardrail effect” of the Alpine foothills facilitates the advance of the cold air.

Wherever this “guardrail” has a gap—that is, wherever a valley entrance opens up from the foothills into the lowlands—cold air flows in from the foothills. The heavy cold air behaves like water that has been poured out onto the foothills and now flows along the edge of the Alps from west to east, like a gutter.

However, this cold air cannot flow directly into the Achental from the west. The pass between Geigelstein and Kampenwand—the Dalsenalm—is far too high for that. So the flat, heavy tongue of cold air sweeps past the north side of Kampenwand and Hochplatte and floods the Achental from the north through the open valley entrance.

This cold air tongue resembles the valley inflow in three ways:
1. It flows parallel to the valley, thus following the twists and turns of the valley.
2. Since it is cold and therefore heavy, its maximum speed occurs very close to the ground.
3. It generates slope updrafts on the same windward slopes as the valley inflow.
The major fundamental difference: the valley inflow is driven by the intra-Alpine thermals further up the valley—that is, from the “suction side.” The cold air flowing into the valley, on the other hand, is driven from the “pressure side.”

From a glider pilot's perspective, the following characteristics are typical of a slope lift driven by cold air flowing into the valley:

  • The prevailing wind is clearly from the west or southwest. Before the cold air front arrives, there is therefore often a light tailwind at the site; flying up the slope is difficult or impossible, or the slope may even be slightly downwind.

  • As the cold air flows into the valley, strong, often gusty headwinds on Run 06 and good slope lift set in very abruptly and suddenly at full strength—quite a surprise!

  • The wind at higher altitudes will remain steady from the west or southwest, since the actual front is still far away.

  • Often, the cold air not only creates very strong updrafts on the slope, but also pushes under the warmer air lying in the valley over a wide area, causing it to rise. This is a lot of fun, because suddenly the air isn't just rising on the slope—it's rising everywhere in the valley!

  • Unfortunately, this splendor doesn't last long: after 20–30 minutes, the entire valley basin is filled with cold air. The lifting process is complete.

  • If the cold-air layer is very thick, it can also fill the higher valley basins located further south, upstream. Otherwise, the flow into the valley comes to a halt as soon as the valley is filled. The slope lift also dies down at that point.

  • Eventually, the actual front, bringing rain, will arrive from the west.

  • Incidentally, the same phenomenon occurs on a smaller scale as well, when—instead of an entire front—a single heavy, stationary shower, strategically positioned at the mouth of a valley, creates such a tongue of cold air.

Although this phenomenon is rare, it’s important to be aware of it and, above all, to recognize it. While it doesn’t result in long or extended flights, it does offer some of the most fun you can have in a valley basin. Example flight: https://www.onlinecontest.org/olc-3.0/gliding/flightinfo.html?dsId=4938095


West Wind
Why can west wind be a problem at all?

Our runway is oriented 06/24, parallel to the valley axis. The valley channels all wind currents so that they run practically parallel to the valley. This channeling is further amplified at the airfield by the slope on one side and the edge of the forest on the other. As a result, we almost never have crosswinds at the airfield; instead, the wind is almost always parallel to the runway—either from the west (wind on Runway 24) or from the east (wind on Runway 06). Unfortunately, we can only perform winch launches in the 06 direction, i.e., toward the east. We also prefer to conduct tow launches on Runway 06, which offers fewer obstacles and better emergency landing options. Wind on Runway 24 therefore means a tailwind for the “normal” takeoff direction, Runway 06. A strong tailwind can impair glider takeoffs or make them completely impossible.

At what wind speed does a westerly wind become a problem?
Of course, it’s difficult to give a blanket answer. You can safely disregard ground-level wind forecasts in the mountains unless you know exactly how they’re calculated and what computational model they’re based on. A better rough guideline is the forecasted wind speed at 1,500 m MSL. This elevation roughly corresponds to the average ridge level of the mountains surrounding the Unterwössen Valley, and this elevation is also commonly found on many weather charts. 1,500 m MSL corresponds to approximately FL050 or 850 hPa. When wind speeds are less than 20 knots at 1,500 m MSL, thevalley inflow systemusually dominates down in the valley on thermal days; driven by intra-Alpine thermals, this system blows into the valley and thus acts as a headwind from the east on Runway 06 at the airfield. At wind speeds of approximately 20 knots or higher at 1,500 m MSL, a westerly wind can set in as a disruptive tailwind.

So do strong westerly conditions always result in tailwinds at ground level?
No, fortunately not. Two different mechanisms protect us from strong westerly winds:

1. Protection from the Mountains
Our valley is well protected to the west by the tall, broad Geigelstein massif (summit 1,808 m) and to the northwest by the Kampenwand. The pass between the two, the Dalsen Saddle, also doesn’t really let much west wind into the Unterwössener Valley, especially since it is, after all, 1,050 meters high. From a broader perspective, it’s also worth noting that by the time the westerly wind reaches us, it has already traveled a long distance over the mountains along the edge of the Bavarian Alps. These mountains, which are about 1,500–2,000 meters high and feature a relief strongly oriented in a north-south direction, significantly slow down the westerly wind in its lower layers. The westerly wind only reaches its full speed once it passes the ridge level. A little further north, however, in the lowlands, this frictional drag is absent. That is why, in westerly conditions, higher wind speeds from higher altitudes reach much lower down there. This is already the case out at Lake Chiemsee.

2. Protection from a Cold Air Pool
At night, the ground radiates its residual heat energy. This causes the ground to cool. This process works particularly well on starry nights when there are no clouds to reflect this heat radiation back toward the ground. The cooled mountain slopes, in turn, cool the layer of air immediately adjacent to them. The air, now colder and therefore denser, slides down the mountain slopes into the valley. There, it accumulates to form a large cold air pool. By the end of a starry night, this pool can easily be several hundred meters thick. In the morning, the air in this cold air pool is initially very stably stratified; after all, it had the entire night to rearrange itself into the most thermally stable state. Incidentally, this is also the reason why you almost never find thermals directly from the wind in the mountains in the morning, and why it’s so rare to get out of a morning stall from an F-tow below 600 meters above ground: the (cold air) lake lies still.

However, this pool of cold air has a major advantage during westerly conditions: it protects us from strong westerly winds. Typically, the air mass brought in by westerly conditions is quite mild. Especially in the fall, the air mass carried in over a short distance from the heat-retaining ocean is often warmer than the pool of cold air that has accumulated overnight in the valley. The mild westerly air at higher elevations is therefore lighter than the heavy cold air that lies more or less still at the bottom of the valley. For this reason, the westerly wind cannot penetrate to the valley floor as long as the cold air remains there.

Side Note: Outflowing Cold Air, Valley Outflow, and Their Names
The heavy cold air naturally follows the valley’s slope and flows slowly out of the valley. This outflow of cold air is also called a “mountain wind” or, more accurately,“valley outflow.” This outflow occurs every morning when a cold air pool is present and is largely independent of any regional wind (e.g., a westerly wind) that may be blowing above the cold air pool. These are therefore two distinct air currents with very different driving forces. Here at the airfield, however, it’s easy to confuse the valley outflow with the westerly wind: even the cold air flowing out of the valley comes—locally at the airfield—from a westerly direction, since the valley happens to slope in a west-east direction here. Accordingly, the valley outflow also results in a local tailwind at the airfield. Nevertheless, it must not be confused with the regional westerly wind. In fact, as early as the next village down the valley—Marquartstein—the valley outflow blows—locally—from the south because it follows the valley as it curves and now slopes from south to north; the same is true a short distance upstream from the airfield at the Klobenstein narrows.
To avoid confusion, it has therefore become standard practice to use the term “west wind” only for a wind blowing from the west on a broader regional scale, as found on weather maps. The same applies, of course, to all other winds named after cardinal directions (north wind, southwest wind, etc.): these are always regional-scale currents. The wind directions of the local valley wind system, on the other hand, are never named after cardinal directions, but rather using the terms “valley-inward” or “valley-inflow” and “valley-outward” or “valley-outflow.”

So why does the west wind sometimes still reach the ground?
Unfortunately, both protective mechanisms (protection from mountains / protection from a cold air pool) can be neutralized—namely by convection, commonly known as thermals. Rising pockets of warm air carry air from the valley upward into the west wind layer above the ridge level. In turn, this creates counterbalancing downdrafts that carry air masses down from the upper levels all the way to the valley floor. These air masses had previously moved along with the prevailing, supraregional westerly wind at higher altitudes. They do not lose this (horizontal) momentum so quickly, even when they are dragged down into the valley by the downdraft. The inertia of the air masses being pulled down causes them to carry “their” westerly wind with them downward. It is also said: “The westerly wind is mixed down to the ground by convection (thermals).”

Can this be predicted?
Since convection (thermals) is a process that is quite chaotic both spatially and temporally, such west wind gusts cannot be predicted as individual events. However, based on the thermal forecast, one can roughly estimate when the risk of strong west wind gusts begins. First, there must be thermals to begin with. This requires appropriate atmospheric layering. Now, the air masses carried by the west wind at high altitudes are typically quite unstable in their layering and thus quite conducive to thermal development. With sufficient sunlight, thermals tend to develop quite early and strongly on the higher slopes that extend into the air mass brought in by the westerly wind at high altitudes. One can then observe small summit clouds early on, which are ruffled by the strong westerly wind and quickly driven downstream. The protection provided by the surrounding mountains is thus weakened. However, as already mentioned, the cold air pool down in the valley is initially very stable in the morning. On top of that, the surface of the cold air pool—with the cold air below and the warmer, mild westerly air above—is nothing other than an inversion. This is also called a valley inversion. Even if there were weak thermals rising from the valley floor down in the cold air pool, they would still remain trapped within the valley inversion.

The valley inversion thus prevents, for a time, any connection between the (already weak at best) thermal activity down in the cold-air pool and the stronger thermals above it. It takes a long time for the cold air to flow out of the valley in part and to be warmed by the beginning sunlight in part. As long as no thermals are rising from the valley floor along the sun-facing slopes all the way up into the westerly wind layer above the ridge level, there will be no counterbalancing downdrafts extending from the upper-level wind down to the valley floor that bring the westerly wind down with them.

As a general rule, the following guidelines can be applied:
Take action early in the following situations:
- high wind speeds just above ridge level
- a thin cold air pool, i.e., after a short and/or overcast night
- a cold air pool that warms up quickly, i.e., after a sunny day
- a good thermal forecast
Take action late in the following situations:
- moderate wind speeds at ridge level and only a gradual increase with altitude
- a thick cold air pool, i.e., after a long (autumn!) and starry night
- a cold air pool that warms up late or not at all, i.e., an overcast day
- a poor thermal forecast
The scenario with a thick cold air pool does, however, have a catch: while the cold air pool does provide particularly effective protection against a penetrating westerly wind, the outflow of cold air out of the valley in turn creates a tailwind at the airfield, as already described in the digression above. On such days, there is sometimes a flyable window after the “normal” morning tailwind ends—due to the outflow of cold air—and before the tailwind sets in—due to a westerly wind mixed down by thermals. Sometimes, however, one tailwind transitions imperceptibly into the other, and one can hardly blame the pilots—who are thus kept grounded all day—for showing only muted enthusiasm for such subtle distinctions between the two mechanisms. Instead, they ask themselves:

Why is a tailwind caused by a mixed-in westerly wind actually so dangerous?
The “normal” morning tailwind, caused by the outflow of cold air that has accumulated in the valley overnight (valley outflow), is uniform, constant, and—due to the stable stratification of the cold air pool—very low in turbulence, almost laminar. Since its driving force is simply the natural slope of the valley, it remains completely free of gusts. Once the reservoir of cold air has gradually dissipated, the valley outflow gradually and continuously subsides.

The westerly wind, however, which has been mixed down by thermal convection, is quite different: the first isolated air pockets, which are dragged down by the downdrafts all the way to the valley floor, suddenly bring the almost undiminished wind speed of the upper-level wind above the ridge level down to the valley floor. A tailwind caused by this mixed-down westerly wind thus sets in harshly, abruptly, and in a manner that is unpredictable in terms of both timing and location. The danger lies not only in the quite high wind speeds, but above all in their sudden onset. After such an air mass has swept through as a westerly gust, a deceptive calm often sets in for several minutes—until the next air mass from above brings the next, equally sudden gust. For this reason, we are extremely cautious both before and during the onset of these gusts and often suspend takeoff operations. This is often difficult for less experienced pilots to understand, especially during longer periods of calm; but the next gust can strike at any moment.

Paradoxically, the tailwind caused by the mixed-down westerly wind becomes somewhat less dangerous once the westerly wind has established itself as a continuous flow all the way to the ground—which often happens after some time of increasing thermal mixing. At least then the wind speed is roughly constant and thus easier to assess. If it isn’t too strong, experienced pilots can sometimes take off again. However, conditions are always unpleasantly turbulent under such circumstances, since the air mass mixed down from higher altitudes is quite unstable to begin with. Thermal activity at the valley floor adds to this.

Will it stay that way for the rest of the day?
Experience shows that, unfortunately, the answer is usually yes: once the westerly wind from higher altitudes has established itself as a continuous flow all the way to the ground, this flow pattern seems to have a certain persistence, even if the thermals visibly subside. At best, late in the afternoon or early in the evening, the west wind may lift off the ground completely once more, but then it stays away. Instead of waiting and hoping for occasional brief windows for individual takeoffs, it might be more worthwhile in this situation to postpone all flying until later in the afternoon.

And how common is this problem?
Unfortunately, we don’t have our own statistics on this. While west is the most common prevailing wind direction in our latitudes, the majority of westerly conditions are either passing fronts (which are rainy anyway, so a tailwind doesn’t matter) or at least so cloudy that not enough thermals can form beneath the shielding cloud cover to mix the westerly wind down to the valley floor. After all, during the summer months, we’re located far enough south in Germany to be distant from the driving low-pressure systems. As a result, in many westerly conditions, the wind speeds simply aren’t high enough to cause the problems described above.


Northern Traffic Jam

What is a stagnation pattern?
Three ingredients are needed for a stagnation pattern: first, wind; second, a moist air mass blowing toward—third—a mountain range. The mountain range forces the wind to rise along the windward slopes. As it rises, the moist air must expand, since atmospheric pressure is lower at higher altitudes. When a gas expands, its temperature decreases (you can look this up under “Ideal Gas Law” or test it yourself with a spray can valve). Eventually, the air in the slope updraft cools so much that the water vapor it contains condenses, becoming liquid. Clouds form (known as orographic clouds), and it may even rain (orographic precipitation).

Under what weather conditions do we experience orographic lifting in our region?
The northern edge of the Bavarian Alps, between Lake Constance and Salzburg, runs roughly from west to east. Any weather conditions with a northerly wind component—from northwest through north to northeast—can therefore potentially lead to orographic conditions, provided that the wind speed at the level of the mountain slopes is high enough and the incoming air mass is sufficiently moist. Naturally, a true north wind causes the strongest uplift because it strikes the edge of the Alps at a right angle. However, northwest orographic conditions are most common after a cold front has passed through.

Shouldn’t there actually be “backside weather” after a cold front passes?
In principle, yes: before a cold front, the regional wind is usually from the southwest; as the front passes, it quickly shifts from the west to the northwest behind the front. In the lowlands, the famous “backside weather” then prevails on the leeward side of the front, characterized by a rapid rise in pressure, clouds clearing quickly, and—despite an initially low cloud base—very good thermals in the unstable cold air. The fresh northwest wind isn’t much of a problem in the lowlands; here on the edge of the Alps, however, it creates a wind-shadow effect, so we don’t experience the backside weather at our launch site, or rather, we can’t take advantage of the new air mass in the mountains until about a day later. On backside days, it’s therefore worth taking a long F-tow north or northwest out into the backside weather in the lowlands. A short distance from the wind-blocked edge of the Alps (often just 10–20 km is enough), you can enjoy beautiful, long lowland flights there. The direct route to Ulm and on to the Swabian Alb has proven reliable; triangles and quadrilaterals of various sizes around the Munich airspace can also be flown in these weather conditions.

Where is the congestion most noticeable?
The diagram shows a north-to-south cross-section of the Northern Alps, from the Upper Bavarian lowlands in the north to the main Alpine ridge in the south.

  1. In the lowlands, there is no stagnation effect; although wind and moisture are present, there are no mountains and thus no lift from slope-side updrafts. Depending on the amount of moisture available, more or fewer cumulus clouds drift along with the airflow; during leeward weather, there may also be the occasional shower in that area.

  2. The air then collides with the edge of the Alps and is lifted by a good thousand meters (the foothills are about 500 m MSL, while the first range of the Bavarian Alps averages about 1,500 m MSL). This 1,000-meter elevation step causes the greatest lift along the entire path of the air mass, resulting in the most significant cooling and, consequently, the most pronounced orographic effect. Here, at the northernmost one or two mountain ranges along the edge of the Alps, the greatest amounts of precipitation accumulate during orographic conditions. In the radar animation, this orographic precipitation can be recognized by the fact that, despite the strong northerly flow, it does not move along with the flow but either persists continuously along the Alpine foothills or (in the case of a somewhat drier air mass) repeatedly forms there and remains there. In contrast, the lines of showers further north in the lowlands move along with the flow.

  3. On the leeward side of the mountains, the airflow slows down again and thus returns to an area of higher air pressure. This leads to compression of the descending air and, consequently, to heating (the ideal gas law—or think of a bicycle pump!), symbolized in the image by the red arrows. This heating can cause clouds to dissipate on the leeward side of the mountains. Unfortunately, you usually don’t notice this yet on the leeward side of the first mountain range; overhanging orographic clouds and precipitation dominate here. Our flight operations are often affected by this, as can be seen from the marked location of the DASSU.

  4. One mountain range further south, deeper into the mountains, the orographic precipitation is already less intense. This is due, in part, to the fact that the elevation gain by which the air mass is now lifted is much smaller—perhaps an additional three hundred meters in altitude, from 1,500 to 1,800 meters MSL. Furthermore, there is now much less moisture present; a large portion of it had already been “stripped away” by the first mountain range. Accordingly, the cloud base of the convective clouds is visibly higher on the windward side of the second range and rises even further on its leeward side.

  5. A similar pattern is repeated along the chain of rugged Northern Limestone Alps, which rise steeply to over 2,500 meters (Innsbruck’s Nordkette, Kaiser, Loferer, Leoganger, Steinernes Meer, Tennengebirge, Dachstein...). It is not the absolute height of the mountains that matters, but rather the additional degree of uplift and the remaining moisture in the air mass. Accordingly, the base of the orographic clouds on the windward side of the Limestone Alps is again somewhat higher; orographic precipitation often fails to occur here at all.

  6. On the long leeward slopes of the Kalkberge, the airflow descends a great distance, becomes compressed, and is thereby heated. This results in a veritable local (northern) foehn effect: Under such conditions, the cloud base on the leeward side of the Kalkberge is significantly higher than on the windward side, and the air mass is considerably dried out as it descends.

  7. This also benefits the thermal flying route of the Pinzgau Walk and its eastern extension (Dientener, Hochgründeck, Rossbrand...): with their relatively low grassy ridges at around 2,000 meters, these mountains are often the first to be clear of clouds during northern barrier conditions. Often, you can already fly in thermals over the ridges here, while on the northern edge of the Alps the base is still too low to fly or there may even be orographic precipitation falling.

  8. It is only on the windward side of the main Alpine ridge that thicker cumulus clouds form again. The degree of lifting there is sufficient to condense the last traces of moisture out of the air mass, which has already dried out considerably. Crossing the main ridge under northerly (wind-sheltered) conditions is therefore always difficult and hard to plan for.

  9. Finally, on the leeward side of the main Alpine ridge, the wind subsides over a wide area; a strong foehn effect causes clouds to dissipate rapidly. The unobstructed sunlight, in turn, generates strong thermals. In the dry air, the base is high—often five hundred meters or more higher than in the north. When conditions like these allow for a successful crossing of the main ridge from north to south, it’s always worth the effort.

How can northern wind patterns be utilized for flying from Unterwössen?

Unfortunately, a northward-moving weather front is probably the most common cause of unflyable, lousy weather in our area. However, if the weather at the launch site even allows for a takeoff, there are various flying options when the wind is from the north. Lowland flights in leeward conditions have already been discussed above. Interesting local flights can also be made even with low, dense weather front clouds in the slope lift along the edge of the Alps (Position 2 in the image above). Between Hochries in the west and Hochstaufen in the east lies a 50-km-long leg that should be flyable in the slope wind starting at a base altitude of about 1,500—preferably 1,600—meters MSL. Mathematically, this would allow for 300 OLC kilometers (example flight: https://www.onlinecontest.org/olc-3.0/gliding/flightinfo.html?dsId=6598740, second half of the flight starting around 1:00 p.m. UTC).

But it can also be very exciting and rewarding to make your way—in a slope wind during a northeasterly traffic jam—around the northern foothills of the Hochplatte all the way to the Aschauer Valley and back home; a base altitude of about 1,000 m MSL is sufficient for this (example flight: https://www.onlinecontest.org/olc-3.0/gliding/flightinfo.html?dsId=6358001 ).

Finally, there are also examples of flights into high mountains during (waning, no longer quite as humid) northern wind-shield conditions. The gradual ascent along the base shown in the diagram—from position 1 to 9—sometimes allows for a step-by-step advance into the mountains, even though clouds are still hanging over the northern edge of the Alps. Being able to reach or even cross the main Alpine ridge on such a day is an incomparable gift (example flights: https://www.onlinecontest.org/olc-3.0/gliding/flightinfo.html?dsId=6559996 and https://www.onlinecontest.org/olc-3.0/gliding/flightinfo.html?dsId=6527854 ).